Professional graphic equaliser with long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution. Sweepable high-pass filter with 20Hz to 500Hz range sets the lower frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for "at a glance" status indication. Invaluable for smooth rejection of unwanted subsonic and low frequencies, particularly relevant with modern, compact wedge monitors. Sweepable low-pass filter with 2kHz to 20kHz range sets the upper frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for at a glance status indication. Provides optimum bandwidth control for vocal monitors and IEM systems. Two sweepable notch filters per channel, with overlapping frequency ranges of 20Hz to 2kHz and 200Hz to 20kHz. These allow precise removal of problem frequencies with minimal effect on the rest of the program material, and fast control of between fader frequencies. This gives precise control of room and loudspeaker resonance/feedback nodes with minimum loss of energy even between ISO centres. The controls each incorporate a push switch to select the filter in and out, with an illuminated ring for "at a glance" status indication.
Long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution
All-new proportional-Q filters provide optimum control without undesirable audio artifacts
Gain control with +6dB/-infinity range and centre detent at unity gain. Allows effective muting of channel in emergencies
Range switch selects ±6dB or ±12dB operation for the faders, with LED indication
Channel bypass switch with LED indication. The unit also provides automatic relay bypass in the event of power failure
Bypass switch with status LEDs for quick comparison of applied EQ
Power switch, fully recessed in the on position to avoid accidental operation
Signal present LEDs show the presence of audio signals above -40dBu
IEC mains inlet, the unit automatically adjusts for operation on all voltages from 100 to 240V AC
KT logo for quality engineering and reliability 3-year KT warranty for peace of mind
Equalizer Type - Graphic Equalizer
Height:
133mm (5.25 inch) (3U High)
Width:
482mm (19 inch)
Depth:
205mm (8 inch)
Product Weight:
12.79 lbs
Shipping Weight:
15.43 lbs
Depth:
8 in
Height:
5.25 in
Width:
19 in
Impedance:
20,000 ohm
Impedance:
20 k?
Input two type:
Electronically balanced (pin 2 hot)
Maximum Input Level:
+22 dBu
Outputs Two type:
Electronically balanced (pin 2 hot)
Minimum Load Impedance:
600 ohms
Source Impedance:
<60 ohms
Maximum Level:
+22 dBu
Frequency Response:
1kHz ±0.5 dBu 20Hz-20kHz
Eq Out:
±0.5 dB
EQ In:
(flat) ±0.5 dB
Distortion (THD+N):
<0.003% at 1kHz,+4dBu
Dynamic Range:
>114 dB (20Hz to 20kHz unweighted, ±12dB range)
Overload Indicator:
+20 dBu
Gain:
-infinitive to +6 dB
Equalisation:
30 Bands
Centre frequencies:
To BS EN ISO 266:1997 25Hz to 20kHz, 1/3 octave tolerance ±5%
Maximum Boost/Cut:
±6/12 dB
High Pass Filter Slope:
12 dB/Octave
Low Pass Filter Slope:
12 dB/Octave
Notch Filter Attenuation:
>17 dB
Q:
32
DN100
- Direct Injection Box with Ground-up Redesign
DN360
- Analogue Graphic Equalizer with Earth Lift Switch Enables Signal and Chassis Grounds
DN500 Plus
- Professional Graphic Equaliser with Long-throw 45mm Oil-damped Faders
DN504 Plus
- Quad Compressor/Limiter with Switchable Knee Function